- New
Monacor Bodega floorstanding speakers Kit with high-end crossover from Hobby HiFi
![rating](/modules/lgcomments//views/img/stars/square/yellow/0stars.png)
Monacor Bodega floorstanding speakers Kit with high-end crossover from Hobby HiFi
Kit with high-end crossover without housing price per speaker
The high-end kit contains Clarity Cap SA 630V capacitors for the tweeter. All coils are designed as baked varnish air coils to reduce the microphonic effect (the current through the coil generates a magnetic field, which in turn sets the winding in motion.
Monacor Bodega floorstanding speakers Kit with high-end crossover from Hobby HiFi
Kit with high-end crossover without housing price per speaker
Bodega is a slim floor-standing loudspeaker with a Monacor chassis. It uses a Monacor SPH-135C as a woofer and the Monacor DT-254 as a tweeter. The loudspeaker was developed by Bernd Timmermanns. The loudspeaker is equipped with a bass reflex housing. The crossover consists of a 2nd order high pass (12 dB/octave) for the tweeter dome. A 2nd order low pass drives the woofer. Two suction circuits smooth out the frequency response of the woofer. The frequency response of the loudspeaker is very linear on axis between 30 Hz and 20,000 Hz. The decay spectrum is almost flawless. The non-linear distortions at medium volumes (90 dB, 1m) are below 0.5% above 500 Hz.
The high-end kit contains Clarity Cap SA 630V capacitors for the tweeter. All coils are designed as baked varnish air coils to reduce the microphonic effect (the current through the coil generates a magnetic field, which in turn sets the winding in motion. This movement induces voltages in the coil, which are added to the useful signal. The tighter the winding of the coil, the less the useful signal is distorted.)
Technical data:
- Impedance: 8 Ohm
- Sound pressure level (2.83V/1m): 80 dB
- Dimensions (HxWxD): 838 x 142 x 300 mm
- Frequency range (-8dB): 24 - 31000 Hz
- Crossover frequency(s): 2000 Hz
- Principle: bass reflex box
Highlights
- Monacor DT-254: dome
- Monacor SPH-135 C mid-woofer
- Insulating fleece MT Bondum 800 (30 x 50 x 2 cm)
- 0.5x PE foam sealing strip, 5x2 mm, roll 7.5 m
- Insulating material Sonofil 100 x 35 cm for 20 liters
- Pole terminals PK31, one pair, gold-plated, red+black
- 2.5m speaker cable 2x1.5 mm2, transparent
- Pan screws 4x20 black, Phillips, 8 pieces
- Construction plan for the kit the crossover components (right), to be assembled on a wooden board.
- Clarity Cap SA capacitor 1.5uF / 630 Vdc
- Clarity Cap SA capacitor 5.6uF / 630 Vdc
- Audaphon MKP CAP Superior 4.7 μF / 400 Vdc
- Audaphon MKP CAP Superior 10 μF / 400 Vdc
- Elko rough, 220 μF/63 Vdc
- Mundorf baked varnish air coil BL71, 0.10 mH/0.23 Ohm
- Mundorf baked varnish air coil BL71, 0.47 mH/0.57 Ohm
- Mundorf baked varnish air coil BL71, 22 mH/5.66 Ohm
- Mundorf baked varnish air coil BL140, 2.7 mH/0.51 Ohm
- Metal oxide resistor MOX10 10 Ohm (brown-black-black
- ) Metal oxide resistor MOX5 2.7 Ohm (red-violet-gold)
- Metal oxide resistor MOX5 4.7 Ohm (yellow-violet-gold) Metal oxide resistor MOX5 6.8 Ohm (blue-gray-gold)
Products from the same category
Products from the same brand