Celestion Tröööt floorstanding speakers Kit with high-end crossover
Kit with high-end crossover without housing, price per speaker
Tröööt is a two-way floorstanding loudspeaker. Tröööt is a bass reflex loudspeaker with chassis from Celestion and Visaton. The loudspeaker contains the following chassis: - a tweeter horn with Celestion CDX1-1747 drive - a Visaton W 300 8 Ohm woofer The loudspeaker was developed by Oliver Martin. The crossover consists of: - a 2nd order high pass (12 dB / octave) for the tweeter. - a 3rd order low pass (18 dB / octave) for the woofer. The frequency response of the loudspeaker is perfectly linear. The decay spectrum (waterfall spectrum) shows a delayed decay behavior in the middle. The non-linear distortions at low volumes (85 dB, 1 m) are below 0.6% above 300 Hz and remain below 1.1% in the audible range even at higher levels (95 dB, 1 m).
The high-end kit is equipped with baked enamel coils to reduce the microphonic effect (the current through the coil generates a magnetic field, which in turn sets the winding in motion. This movement induces voltages in the coil, which are added to the useful signal. The tighter the winding of the coil, the less the useful signal is distorted.) The capacitor for the Celestion CDX1-1747 - where quality is particularly important - is a high-quality Clarity Cap CSA MKP capacitor with 250 V.
.
Technical data:
- Impedance: 8 Ohm
- Sound pressure level (2.83V/1m): 90 dB
- Dimensions (HxWxD): 760 x 520 x 400 mm
- Frequency range (-8dB): 38 - 20000 Hz
- Crossover frequency(s): 1100 Hz
- Principle: bass reflex box
.
Highlights
- Visaton W300, 8 Ohm
- Celestion CDX1-1747, 1.75 inch Kapton driver
- 0.5x PE foam sealing strip, 5x2 mm, roll 7.5 m
- 2x Sonofil insulation material 100 x 35 cm for 20 liters
- Convoluted foam N25-30, 100x50cm, anthracite
- Biwiring terminal T122 Au with gold-plated brass terminals
- 3m speaker cable 2x2.5 mm2, transparent
- Pan screws 4x20 black, Torx, 8 pieces
- Construction plan for the kit the crossover components (right), to be assembled on a wooden board.
- ClarityCap CSA capacitor 5.6μF / 250 Vdc
- ClarityCap ESA capacitor 1 μF; / 250 Vdc
- Audaphon MKP CAP Superior 4.7 μF; / 400 Vdc
- Audaphon MKP CAP Superior 22 μF; / 400 Vdc
- Audaphon MKT capacitor 6.8 μF; / 160 Vdc
- Audaphon MKT capacitor 33 μF; / 160 Vdc
- Mundorf baked varnish air coil BL71, 3.3 mH/1.75 Ohm
- Mundorf baked varnish air coil BL100, 0.82 mH/0.45 Ohm
- Mundorf baked varnish air coil BL100, 2.2 mH/0.83 Ohm
- Ceramic resistor 8.2 Ohm/20 Watt
- Metal oxide resistor MOX10 2.7 Ohm (red-violet-gold)
- 2x metal oxide resistor MOX10 22 Ohm (red-red-black)