- New
Audaphon Athena floorstanding speakers Kit with high-end crossover
![rating](/modules/lgcomments//views/img/stars/square/yellow/0stars.png)
Audaphon Athena floorstanding speakers Kit with high-end crossover
Kit with high-end crossover without housing, price per speaker
The high-end kit is equipped with baked varnish coils in the important places to reduce the microphonic effect (the current through the coil generates a magnetic field, which in turn sets the winding in motion.
Audaphon Athena floorstanding speakers Kit with high-end crossover
Kit with high-end crossover without housing, price per speaker
Athena is a three-way floorstanding loudspeaker with very low distortion. Athena is a bass reflex loudspeaker with chassis from Audaphon and Wavecor. The loudspeaker contains the following chassis: - an air motion transformer (ribbon tweeter) Audaphon AMT 1i - a midrange speaker Wavecor WF182CU13 - a woofer Wavecor WF223BD01 The loudspeaker was developed by David Hahn. The crossover consists of: - a 2nd order high pass (12 dB / octave) for the tweeter. - a band pass consisting of a 2nd order high pass (12 dB / octave) and a 3rd order low pass (18 dB / octave) for the mid-woofer. - a 2nd order low pass (12 dB / octave) for the woofer. The frequency response of the loudspeaker is perfectly linear. The decay spectrum (waterfall diagram) is exemplary without any disturbing resonance. The non-linear distortions at low volumes (85 dB, 1 m) are below 0.6% above 300 Hz and remain below 0.6% in the audible range even at higher levels (95 dB, 1 m). At 85 dB, the non-linear distortions above 700 Hz remain almost consistently below 0.1%
.
Technical data:
- Impedance: 3 Ohm
- Sound pressure level (2.83V/1m): 90 dB
- Dimensions (HxWxD): 1150 x 250 x 300 mm
- Frequency range (-8dB): 32 - 30000 Hz
- Crossover frequency(s): 230, 2000 Hz
- Principle: bass reflex box
.
Highlights
- Wavecor WF182CU13, 8 Ohm, paper, BD, phase plug
- Audaphon AMT-1i
- Wavecor WF223BD01, 4 Ohm, mid-woofer paper / fiberglass
- Bass reflex tube HP100, 100x197 mm, black
- 2x insulation fleece MT Bondum 800 (30 x 50 x 2 cm)
- Insulation material Sonofil 100 x 35 cm for 20 liters
- Pole terminals PK28 I, one pair, gold-plated, red + black
- 3m speaker cable 2x1.5 mm2, transparent
- Pan screws 3.5x17 black, Torx, 8 pieces
- Pan screws 4x20 black, Torx, 8 pieces
- Construction plan for the kit the crossover components (right), to be assembled on a wooden board.
- ClarityCap PWA capacitor 100 μF / 160 Vdc
- ClarityCap CSA capacitor 1.5μF / 630 Vdc
- ClarityCap CSA capacitor 8.2μF / 630 Vdc
- Audaphon MKP CAP Superior 12 μF / 400 Vdc
- Audaphon MKT capacitor 100 μF / 160 Vdc
- Mundorf baked varnish air coil BL71, 0.39 mH/0.51 Ohm
- Mundorf baked varnish air coil BL71, 6.8 mH/2.68 Ohm
- Mundorf baked varnish air coil BL140, 0.68 mH/0.23 Ohm
- Mundorf baked varnish air coil BL140, 1.5 mH/0.38 Ohm
- Mundorf H-core baked varnish coil BH140, 4.7 mH/0.26 0hm
- Metal oxide resistor MOX10 3.9 Ohm (orange-white-gold)
- Metal oxide resistor MOX10 6.8 Ohm (blue-grey-gold)
Products from the same category
Products from the same brand